Drag Cars, Drag Tech & Drag Racing Action!


Drag Cars

Pro Mod

Pro Street

Street Rods

Drag Racing Parts

Drag Racing Intakes

Drag Racing Heads

Drag Racing ECU Upgrades

Drag Racing Headers

Drag Racing Nitrous Kits

Drag Racing Pistons

Drag Racing Fuel Pumps

Drag Racing Flywheels

Drag Racing Exhaust Systems

Cylinder Head Porting

The Notorious Nitro Engine

The Explosive Facts About Racing Fuels

Roots Supercharger

Nitro Funny Car

The Delay Box

The HANS Device

Drag Racing History Insight

Classic Car Parts

Muscle Cars

Search for drag racing parts:



This for sale has been viewed times.


You will receive every stud needed to install both cylinder heads on your engine.

For use with most BBC aftermarket aluminum heads, including our Procomp AFR aluminum heads.

These head studs are made from aircraft quality 8740 high tensile strength chrome moly steel.190,000 PSI kit that comes complete with 12 point hex nuts and washers. Very similar or rather identical in design and function to the ARP kits.

  • Studs make head installation a lot easier as the studs align the head and hold the head gasket in place
  • They are twice as strong (190,000 psi steel alloy) as the stock head bolts
  • They clamp much better since the stud is loosely threaded into the block and the clamping torque is generated at the stud-nut interface rather than the block-bolt interface

Studs are superior to head bolts. And for good reason. Using studs will make it much easier to assemble an engine (especially a racing power plant which must be serviced frequently and quickly!) with the cylinder head and gasket assured of proper alignment.

Studs also provide more accurate and consistent torque loading. Here s why. When you use bolts to secure the head, the fastener is actually being "twisted" while it s being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A stud should be installed in a "relaxed" mode - never crank it in tightly using a jammed nut. You do not necessary have to bottom out the stud if your when installing if your short a few threads on the top side. If your stud is screwed into the block approximately 125% deeper than the diameter of the stud, then this is sufficient.

If everything is right, the stud should be installed finger tight or less if needed. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. Remember, an undercut shorter stud will have a rate similar to a longer, standard shank stud. This provides a more even clamping force on the head. Because the head gasket will compress upon initial torquing, make sure studs and bolts are re-torqued after the engine has been run. If you have an application or technical question feel free to call or email us.

We strive to keep our prices low, and due to the high volume that we purchase, this allows us to have the best price in the country. Many garages will buy several sets at a time just to have them if the need arises. Our shipping prices are usually the lowest you will find..

On a high mileage engine, or a performance engine, it s risky to reuse the original head bolts because the engine may have been torn down several times already. It s much safer to toss the old head bolts and install our new stud set.

As the head gets hot, thermal expansion is going to stretch the head bolts even more - especially in engines with aluminum heads. Aluminum expands at more than twice the rate of cast iron, which puts even more strain on the head bolts, and this is one more area that head studs prevail. In a typical engine, just warming the engine up to normal operating temperature may stretch the head bolts as much as .005? or more, another good reason for replacing fatigued head bolts with head studs.

Used head bolts have a reduced clamping force. That s a fact. The more the bolt has been used, the less effective it is in clamping down, and is more prone to loosening. Age is also a factor, as time also increases stretch, due to the heat cycles the bolts have encountered. We can tell you this much for sure, a good way to blow a head gasket is to use the old head bolts from your engine. We never do this. Studs are the way to go.

Perfect for all aluminum heads Replacing old head bolts is a must when installing new heads.

These are the correct length for most any of the bbc aftermarket aluminum heads on the market. We have built at least 20 engines using these head studs.

Spending huge amount of money on head bolts is not necessary in our opinion. We use our head stud set on engines that run 13.5 to 1 compression, and never have a problem.

Using stock stretched head bolts is the worst thing you can do, especially on aluminum heads. Don t even consider it.

When installing aluminum heads on any engine, be sure you run a tap down all cylinder head bolt holes in the block. This ensures that the threads are smooth and clean, which will help give a true torque reading when the head studs are tightened. Some engine builders choose to lubricate the threads of the studs, with 20- or 30-wt. engine oil, or an equivalent thread lubricant before the head studs are torqued. Also, make sure the threads and shanks are clean and free of any foreign matter that may cause false torque readings.

Check stud lengths. Make sure you have the correct length for the application and for each hole location (some holes require longer or shorter studs than others). If a stud is too short and only engages a few threads in the block, it may pull the threads out of the block.

Very Important Note!

Our sales staff has limited technical knowledge on this product and are usually unable to answer many of the questions asked. See our other listings for any variations of this product.

    • We are not responsible for collateral damage caused by the use of this product.


Should a problem occur, please contact us. If a return is necessary, please contact us for an RGA number and return authorization. The RGA number must be included on the return label. If an item is returned without an RGA number, it will not be processed. A full description of what the problem is needs to be included with any returned product with your contact info, and proof of purchase. Even though you may have explained the problem to us, and been granted permission to return the product, we must have a written explanation and a contact number included with the product. It is also recommended that you include the name of the person from our company that you have been in contact with. You must send the item back to us in a trackable manner (USPS Priority Mail, FedEx, etc.) and keep the tracking info of the returned product. Please give ample time for returns to be processed. Following these guidelines will make the return process work as it should.


We offer great discounts on shipping. You only paythe full shipping fee on the highest shipping cost of your items, andHALF PRICEshipping on all additional items. Few offer discounts on shipping such as this. Our checkout system will automatically calculate your shipping discount at the time of final payment, providing you consolidate your payment.

You may receive a verification and tracking number shortly after purchase, but this does not necessarily mean that your product has shipped. It would be fair to say that 98% of products will be going out the day the shipping label is issued. On occasion, the product may not ship out until the next day after the label has been issued. Most products purchased late in the day will not be shipped until the next day.

If you checkout and start over, the auto calculator will not recognize the multiple purchases, and there will be no shipping discount.

Buy Now



Copyright © 2001-2009 DragCars.com(TM). All Rights Reserved..

Contact Us 

Legal Policy